Public Safety Digital Single Band PICO Repeate

Helios® Public Safety Digital Single Band Repeaters employ Software Defined Radio (SDR) technology based upon our FPGA & DSP Platform. This achieves high out of-band rejection and high intra-Carrier interference compared to traditional Analog IF SAW filters. It also enables on-the-fly filter change/upgrade by software without an expensive hardware upgrade. Software based “time slot AGC” and “time slot squelch” mechanism for channelized repeaters which reduces noise transmitted to the base station thus improving overall network performance and selectivity.

Helios® Public Safety equipment helps to extend the coverage of Public Safety and Critical secure Communications Networks. Helios offers complete and integrated solutions for TETRA, DMR, PMR, P25 and LTE Networks to ensure coverage of major public infrastructure; such as police stations, garages, power plants, exhibition halls, airports, sports arenas, road and rail tunnels, hotels, convention centers, shopping malls, office towers, parking lots etc.

The Repeater is connected via coaxial cable to a Donor Antenna and Service Antenna or DAS. The Donor Antenna is placed outside the building where it has access to a BTS signal, and the Service Antenna or DAS are placed in the building where they can extend radio coverage to the areas lacking coverage.


Key Feature

  • Single Band operating supporting major public safety bands including 400MHz, 700MHz or 800MHz.

  • Supports all major public safety technologies include TETRA, DMR, PMR, P25 and LTE.

  • Band Selective or Channelized based upon Software Defined Filtering, and BW or number of filters can be tunable or upgradeable by software.

  • SOC & embedded architecture enable delivery of significantly improved network coverage with very low power consumption.

  • Supports upgrading filter parameters in case of frequency re-farming by software.

  • Better out of band rejection than analog SAW filters.

  • Optional ICS function for band selective filter design.

  • Built-in Micro USB interface for local control.

  • Built-in 2G or 3G or 4G wireless modem as option for SNMP trap function.

  • Built-in individual AGC & ALC functions for each sub-band.

  • RF composite power +13dBm to +18dBm for small coverage application.

  • High working Gain min. 75dB and cost-effective solution making coverage more affordable for small building or driving a DAS in large buildings.


Application

To expand public safety signal coverage of fill signal blind area where signal is weak or unavailable.

  • Outdoor: Airports, sports arenas, road and rail tunnels etc.

  • Indoor: Hotels, police stations, garages, power plants, exhibition halls, convention centers, shopping malls, office towers, parking lots etc.


SPECIFICATION
  • Frequency

    Single band operating supporting all major public safety frequency bands including 400MHz, 700MHz or 800MHz

  • Bands Support

    Supports all major public safety technologies include TETRA, DMR, PMR, P25 and LTE.

  • Filter Design

    Band Selective or Channelized based upon Software Defined Filtering, and BW or number of filters can be tunable or upgradeable by software. * Contact your local Helios Solutions sales representative to get more details for multiple sub-bands or channels requirement.

  • Max Gain

    75dB (+/-2dB)

  • Ripple in Band

    +/- 2.5dB

  • Max RF Composite Power

    +13dBm, +15dBm, +18dBm

  • AGC Range

    Max 30dB

  • Noise Figure

    Max 6dB @ Max Gain

  • Time Delay

    Max 12µs (depending on filter bandwidth and required adjacent channel rejection)

  • Local Monitor & Control

    LED Indicator and Laptop via LMT and USB port to monitor & Control Power on/off, Over Power, Oscillation Detection, Isolation Measurement, Door Status, Temperature, Power Supply, VSWR, Output Power, Gain, ATT and etc.

  • Remote Monitor & Control

    Via Helios Netview OMC Software + Option embedded 2G/3G/4G Wireless Modem + Chargeable Li-ion Battery, SNMP V3 compatible

  • Connector

    2*N-Type Female, 1*USB Port

  • Mounting Type

    Wall Mount

  • Power Supply

    110/240VAC

  • Complies with

    ETSI EN 302 561 V2.1.1, ETSI TS 101 789-1 V1.1.2 (2007-04), EN 301 489-05 V2.2.0, ETSI TS 136 106